ACCELERATOR UNIT 18919-AM810 for TCM

If you are unsure that this is your correct part, please message us on chat, or call us toll-free: 1855-585-4430

Buy with confidence!

* Made with the Highest Quality Components Available

* Quality tested items with unsurpassed reliability

* Multiple shipping locations for faster delivery

Product Description

This is an Accelerator Unit pedal position Sensor with Part Number: 18919-AM810.

This part is also listed under the following part numbers:

* AC18919-AM810

* KO18919-AM810

* TC18919-AM810

Application: This 18919-AM810 Accelerator Unit fits following models J15 Engine forklifts:

Product Specifications:

Specifications of the 18919 AM810 Accelerator Unit:

18919-AM810 Accelerator Unit

This is a 18919 AM810 Accelerator Unit for TCM, Nissan 350Z G35 and FX35 FX45, along with other brands and models. This 18919-AM810 Accelerator Unit Consist of 6 pins which are connected with six wires from the accelerator pedal position sensor. The accelerator pedal position sensor is a throttle position sensor with the paddle attached.

Pin # 6 and Pin # 4 = Connected with Power Supply

Pin # 3 and Pin # 1 = Ground

Pin # 5 and Pin # 2 = Signal 1 and 2

Inside the unit, two potentiometers give Signal 1 and 2 on Pin # 5 and 2, which then pass the signal to the throttle or 18012-FK10A accelerator pedal which controls fuel supply to the engine. 

Figure: 18919-AM810 Accelerator Unit For Nissan Komatsu & Allis-Chalmers, TCM Forklift

Figure: 18919-AM810 Accelerator Unit For Nissan Komatsu & Allis-Chalmers, TCM Forklift

Figure: 18919-AM810 Accelerator Unit For Nissan Komatsu & Allis-Chalmers, TCM Forklift

Warranty Information

With the purchase of 18919-AM810 Accelerator Unit from Sourcefy, a 1-year limited warranty is included.

Frequently Asked Questions

Is this an OEM part?

No, it is an aftermarket 18919-AM810 Accelerator pedal sensor unit for Nissan Komatsu & Allis-Chalmers, TCM Forklift.

What is an accelerator pedal position sensor?

It is a sensor that keeps track of where the accelerator pedal is positioned and transmits that information to the powertrain control module.

What does a vehicle sensor do?

The vehicle sensor is the input device of the vehicle computer system. It converts the information of various working conditions during the operation of the vehicle, such as vehicle speed, the temperature of multiple media, and engine operating conditions, into electrical signals and sends them to the computer so that the machine is in the best working condition. 

How does the accelerator pedal sensor work?

The accelerator pedal position uses a sensor that locates the pedal using a magnetic field to identify its location. A change in the pedal's position causes a difference in the charge. The ECM receives the information to let it know how firmly you are depressing the gas pedal.

How do I reset my accelerator pedal sensor?

Here is how you can reset your accelerator pedal sensor:

* Disconnect the battery for approximately five minutes

* After five minutes, reconnect the battery

* Turn the ignition switch on

* Press the gas pedal and release: Repeat this step 2 to 3 times

* Turn the ignition switch off

* Check if the idle is still, then it's reset successfully

When should I replace my accelerator pedal sensor?

If you find the following problems, then it's likely to replace your accelerator pedal sensor:

* Bad idling

* The engine does not run efficiently

* Vehicle acceleration issues

* Jerks while depressing the throttle paddle.

Need More Parts? 

Are you looking for something else? Please browse our Forklift Parts Catalog here. Sourcefy provides quality original and aftermarket parts at a very reasonable price. All parts come with a limited 1 Year Warranty. We also guarantee a 100% fit for our parts.

Please Note: The actual product may vary slightly in color and appearance. The images are for illustration purposes only.